自干钢化玻璃油墨钢化玻璃自干油墨

使用微信扫描二维码分享朋友圈，成交更快更简单！

自干钢化玻璃油墨钢化玻璃自干油墨

本产品主要用于各种玻璃,钢化玻璃,汽车,彩晶玻璃,微晶玻璃,玻璃器皿,玻璃奶瓶,高硼硅玻璃,玻璃盖板,玻璃镜片,手机玻璃,家电玻璃,工业玻璃,日用玻璃,玻璃灯管,玻璃仪器等制品的丝印及移印。
2,产品特性：高亮光/平光哑光,附着力佳,快干,耐溶剂,耐高温,耐摩擦,耐酸碱,抗腐蚀,耐水煮,耐刮伤环保无卤素。
3,稀释剂：用我司B-03稀释剂或783开油,用718洗网水清洗网版。
4,固化剂：单组份使用,也可选择添加我司JS-10固化剂用于增加油墨附着力及物理化学抗性。
5,油墨调配方法：开罐先搅拌均匀,取所需量油墨稀释到合适印刷粘度。如需添加固化剂,先加固化剂搅拌后静置10分钟,待油墨与固化剂完全交联后再进行稀释。
6,干燥时间：常温干燥,表干时间5-10分钟,实干时间在24小时以内,80℃烘烤20分钟可快速干燥。
7,添加固化剂后的使用时限：4-6小时,过期请弃用,剩余油墨不可回收。
【性能检测】
1,3M胶带划百格测试：无脱落
2,耐冲压测试：1mm厚铝板180°折弯无变化。
3,耐酒精测试：用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。
【注意事项】
1,先小量试印确认符合要求后再批量生产。
2,做好承印物的表面清除油脂及杂质工作,以促进附着效果。
3,附着力,硬度,耐酸性,耐酒精性,耐化学品性,抗划伤性,耐磨性等性能的检测,
需要完全固化后方可检测。
4,未经允许情况下,不得将本系列油墨与其它类型油墨混用及配色。
5,油墨,稀释剂使用及储存时严禁烟火。
6,使用时注意施工场所的通风状况良好,尽量避免皮肤直接接触。
7,本品不慎溅入口,鼻,眼,耳内,应用大量水清洗或直接求助医生。
This product is mainly used for all kinds of glass, toughened glass, automobile, color crystal glass, glass ceramics, glassware, glass bottles, high borosilicate glass, glass plate, glass lens, mobile phone glass, household glass, glass industry, daily-use glass, glass tube, glass and other equipment products and silk screen printing.
2, the product characteristics: high gloss / Matt matte, attachment Lijia, quick drying, solvent, high temperature resistance, friction resistance, acid and alkali resistance, corrosion resistance, boiling water resistance, resistance to scratching environment-friendly halogen-free.
3, the thinner: with our B-03 special thinner or 783 oil, 718 washing network water cleaning screen.
4, curing agent: use single component, choose to add our JS-10 special curing agent used to increase the ink adhesion and physical and chemical resistance.
5, ink deployment method: open the tank to stir evenly, take the required amount of ink to dilute the appropriate printing viscosity. For the need to add the curing agent, first add the curing agent after stirring for 10 minutes, until the ink and curing agent is fully cross-linked and then diluted.
6, the drying time: at room temperature, dry time 5-10 minutes, working hours in 24 hours, 80 degrees bake 20 minutes can be fast drying.
7, add curing agent after the use of time: 4-6 hours, please not expired, the remaining ink Unrecyclable.
[performance test]
1, 3M tape to draw 100 cell test: no shedding
2, resistance to stamping test: 1mm thick aluminum plate 180 bending no change.
3, resistance to alcohol test: use skim cotton dipped in concentration of 99% industrial alcohol with 500G force level back and forth 200 times without decolorization.
[note] [note]
1, a small amount of the first test to confirm compliance with the requirements of mass production.
2, do a good job in the surface of the substrate to remove grease and impurities work to promote the attachment effect.
3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, wear resistance and other properties of the test,
Need to be fully cured rear can be detected.
4, without permission, may not use the series of ink and other types of ink mixing and matching.
5, ink, thinner use and storage is prohibited fireworks.
6, pay attention to the use of the construction site ventilation condition is good, try to avoid direct contact with skin.
7, the product accidentally splashed entrance, nose, eyes, ears, the a